-

-

+90(212)320 36 50
4,6681
$3,7941
PSFN  140 2.Kademe
  • PSFN  140 2.Kademe
Marka: NEUGART

Seri:PSFN SERİSİ BOŞLUKSUZ REDÜKTÖRLER

Model: PSFN 140 2.Kademe

Model Birim Fiyat Birim Fiyat Adet Stok
PSFN 140 2.KademeNeugart Planet Redüktör Tahvil Oranı:16,20,25,35,40,50,70,100Fiyat Sorunuz: 0212 320 36 50
  • Ürün Hakkında
  • Dokümanlar
  • Yazılımlar
Helis Dişli Yeni Tasarım
Düşük Boşluk ( 1 arcmin)
Yüksek Çıkış Torku (max 2440Nm)
Yüksek Verimlilik (max 98)
Gürültüsüz Çalışma (61-76 dB)
2 Kademeye Kadar 12 Farklı Çevrim Oranı
30000 Saat Çalışma Ömrü
Çalışma Sıcaklığı: -25°C ÷ +90°C
Koruma Sınıfı: IP65


    --------------------PSFN Katalog.pdf-----------------
    82 Low-noise, with optimized synchronized speed, designed for PSFN - line high radial forces The next generation of helical-cut ? ange gearheads. Excellent torsional stiffness, premium dynamics, silent, optimized synchronized speed. The output dimensions of this series are compatible with those of the straight geared PLFN series helical geared new PSFN PSFN83 • Low backlash <3 arcmin (<1 arcmin optional) • High output torque - the industry‘s highest torque density • Highest torsional stiffness • Precise, easy, and flexible motor mounting • High efficiency (up to 98%) • Ground and honed gearing • 12 ratios 4:1 to 100:1 • Low noise (<65 dB(A)) • Consistent quality (ISO 9001 and 14001) • Operable in any mounting positions • Lifetime lubrication • Numerous options • Output flange similar to EN ISO 9409 • Input and output rotate in the same direction 1 Technical data Page 84 2 Dimensions Page 87 3 Possible motor mounting Page 111 4 Ordering code/Options Page 107 5 Conversion table Page 118 6 Gearhead sizing/selection Page 120 7 CAD drawings. dimension sheets www.neugartusa.com 8 Sizing/calculation/selection NCP Software page Options 10 8 PSFN PSFN84 PSFN - line Technical data (2) Gearbox type PSFN Z Gearbox life at full load 20,000 h Gearbox life at 88% nominal torque T x 0,88 30,000 2N 98 1 (6) E? ciency at full load % 95 2 (4) Min. operating temp. -25 °C (4) Max. operating temp. 90 Protection class IP 65 Lubrication lifetime lubrication Mounting position any Recommended motor ? ange / shaft tolerance DIN 42955-R (1) (2) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i Z 39 80 180 470 950 4 40 80 175 405 950 5 1 37 78 175 355 900 7 28 59 140 305 750 10 39 80 180 450 950 16 39 80 180 450 950 20 Nominal (rated continous duty) Nm (3)(5) Output torque T 2N 40 80 175 405 950 25 40 80 175 405 950 35 2 39 80 180 470 950 40 40 80 175 405 950 50 37 78 175 355 900 70 28 59 140 305 750 100 (1) (2) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i Z 62 128 288 752 1520 4 64 128 280 648 1520 5 1 59 125 280 568 1440 7 45 94 224 488 1200 10 62 128 288 720 1520 16 62 128 288 720 1520 20 Output torque sustainable 30,000 output shaft Nm (3)(5) rotations 64 128 280 648 1520 25 64 128 280 648 1520 35 2 62 128 288 752 1520 40 64 128 280 648 1520 50 59 125 280 568 1440 70 45 94 224 488 1200 100 (1) Ratio (i=n /n ) 1 rpm high speed side 2 rpm low speed side (2) Number of gear stages (3) Values reference output shaft speed n =100 rpm. S1= 100% duty cycle. 2 K =1 application factor and T=30°C. 86 F ambient temperature A (4) Measured at the middle of the gearbox housing surface (5) Dependent on the motor shaft diameter (6) Ratio dependent; based on n =100 rpm output shaft speed 2 PSFN85 PSFN - line Technical data (2) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 Z < 3 < 3 < 3 < 3 < 3 1 Standard backlash arcmin < 5 < 5 < 5 < 5 < 5 2 (8) Optional reduced backlash <2 <1 <1 <1 <1 (3)(4) Fr for 20,000 h 2400 4400 5500 12000 23000 (3)(4) Fa for 20,000 h 4300 8200 9500 8500 16000 N (3)(4) Fr for 30,000 h 2100 3900 4800 11000 21000 (3)(4) Fa for 30,000 h 3800 7200 8400 7500 14000 16 35 90 200 650 1 Nm / Torsional sti? ness arcmin 14 30 80 180 550 2 1.5 3 6.5 12 28.3 1 Weight kg 2.2 4 8 13.5 32 2 (5) Running noise dB(A) 57 58 63 66 68 14000 10000 8500 6500 6000 1 (6) Max.recommend input speed min-1 14000 14000 10000 8500 6500 2 (1) (2) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i Z 120 280 650 1650 3200 4 130 280 650 1650 3200 5 1 80 175 340 1300 3200 7 90 200 480 600 1700 10 150 300 650 1650 3200 16 150 300 650 1650 3200 20 Nm (7) Emergency stop torque (lbin) 150 300 650 1650 3200 25 150 300 650 1650 3200 35 2 150 300 650 1650 3200 40 150 300 650 1650 3200 50 80 175 340 1300 3200 70 90 200 480 600 1700 100 (1) Ratio (i=n /n ) 1 rpm high speed side 2 rpm low speed side (2) Number of gear stages (3) Values reference output shaft speed n =100 rpm. S1= 100% duty cycle. 2 K =1 application factor and T=30°C. 86 F ambient temperature A (4) Measured at the middle of the output shaft (5) Sound pressure level measured 1 m from the gearbox for ratio 5:1 at 3000 input rpm and no load (6) Recommended gearbox operating temperature should not be exceeded. consult Neugart in case higher than listed rpm is required (7) Permissible about 1000 times during the gearbox life (8) Ordering code and options see page 107 PSFN86 PSFN - line Technical data (1) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i 0.192 0.630 1.811 10.647 45.173 4 0.163 0.484 1.347 9.063 36.268 5 0.138 0.376 1.044 7.733 28.706 7 0.125 0.319 0.862 7.048 24.718 10 0.175 0.195 0.581 1.913 10.876 16 0.152 0.165 0.453 1.437 9.208 20 (2) Mass moment of inertia kgcm² 0.151 0.159 0.434 1.348 8.852 25 0.131 0.136 0.350 1.058 7.652 35 0.123 0.126 0.311 0.911 7.084 40 0.122 0.124 0.307 0.892 6.995 50 0.122 0.123 0.304 0.891 6.922 70 0.122 0.123 0.302 0.884 6.880 100 (1) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i 3200 2400 1800 1100 750 4 3800 2950 2250 1350 950 5 4500 3800 2950 1800 1250 7 4500 4000 3500 2300 1700 10 4500 4500 3800 2450 1550 16 4500 4500 4000 3050 1900 20 Recommended max. mean input speed at -1 min (3)(4) 50% rated continuous duty torque (S ) 1 4500 4500 4000 3350 2050 25 4500 4500 4000 3500 2650 35 4500 4500 4000 3500 3000 40 4500 4500 4000 3500 3000 50 4500 4500 4000 3500 3000 70 4500 4500 4000 3500 3000 100 (1) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 i 3000 2250 1700 1000 700 4 3600 2750 2050 1250 850 5 4500 3550 2750 1650 1150 7 4500 4000 3500 2150 1550 10 4500 4500 3550 2250 1400 16 4500 4500 4000 2750 1700 20 Recommended max. mean input speed at -1 min (3)(4) 100% rated continuous duty torque (S ) 1 4500 4500 4000 3100 1900 25 4500 4500 4000 3500 2450 35 4500 4500 4000 3500 2800 40 4500 4500 4000 3500 3000 50 4500 4500 4000 3500 3000 70 4500 4500 4000 3500 3000 100 (1) Ratio (i=n /n ) 1 rpm high speed side 2 rpm low speed side (2) The moment of inertia relates to the high speed side (typically motor shaft) (3) Recommended gearbox operating temperature should not be exceeded. consult Neugart in case higher than listed rpm is required (4) Exact definition see page 123 PSFN D22 87 PSFN - line Dimensions output flange according to EN ISO 9409 L1 with additional mounting holes L13 L12 D17 D17 R1 L8 L11 Q3 D16 L22 R1 L21 L10 Fw L5 L20 G3 (2) Type-Size PSFN 64 PSFN 90 PSFN 110 PSFN 140 PSFN 200 Z All dimensions in mm D10 Pilot diameter H7 20 31.5 40 50 80 D11 Hole circle diameter 31.5 50 63 80 125 D12 Pilot diameter 40 63 80 100 160 h7 D13 Pilot diameter 64 90 110 140 200 D14 Outside diameter 86 118 145 179 247 D16 Motor mounting hole diameter 4.5 8x45° 5.5 8x45° 5.5 8x22.5° 6.6 12x30° 9 12x30° D17 Hole circle diameter 79 109 135 168 233 11 14 19 24 32 1 (1)(4) D20 Motor mounting hole diameter 11 11 1 4 1 9 2 4 2 60 80 95 130 180 1 (1) D21 Motor centering pilot diameter 60 60 80 95 130 2 75 100 115 165 215 1 (1) D22 Hole circle diameter 75 75 100 115 165 2 90 115 145 185 260 1 D23 Motor matching adapter diagonal 90 90 115 145 190 2 Fw Chamfer angle ° 35555 M6x12 M8x15 M10x20 G2 Thread x depth M5x7 8x45° M6x10 8x45° 12x30° 12x30° 12x30° M5x10 M6x12 M8x16 M10x20 M12x24 1 (1) G3 Mounting hole thread x depth 4x M5x10 M5x10 M6x12 M8x16 M10x20 2 71 89.5 108 142 172 1 (3) L1 Overall length 99.5 111.5 130 173 217 2 L5 Chamfer length 6 11.5 10.5 17 24.5 L8 Flange width 4 7 8 10 12 L10 Length of centering 4.5 6.5 6.5 6.5 10 L11 Pilot length 36667 L12 Pilot length 10 12 12 14 17.5 L13 Length of output ? ange 19.5 30 29 38 50 23 30 40 50 60 1 (3) L20 Reference motor shaft length 23 23 30 40 50 2 3 3.5 3.5 4 6 1 L21 Motor pilot depth 3 3 3.5 3.5 4 2 25.5 31.5 43.5 50.5 67.5 1 (3) L22 Reference motor adapter ? ange width 25.5 25.5 31.5 51.5 50 2 70 90 115 150 210 1 (1) Q3 Min. Flange square 70 70 90 115 150 2 (1) Dimensions reference to the mounted motor-type (2) Number of gear stages (3) For longer motor shaft > L20, actual minimal L22 dimension = L22 + (Motor shaft length - L20 ) ; L1 = L2 + L3 + L22 (4) For shaft fit j6 to k6 2 stage drawing available in the TEC Data Finder under www.neugartusa.com D21 D20 G2 D10 D11 D12 D13 D14 PSFN
    E-endustri.com'u takip edin
    e-endustri.com Hesaplı Alışveriş Kredi kartları